Komatsu PC490LCi-11 LARGE EXCAVATORS

Komatsu PC490LCi-11 LARGE EXCAVATORS

BucketCapacityMax 4.15
BucketCapacityMin 1.47
Horsepower 359 @1900 rpm
OperatingWeightMax 107850
OperatingWeightMin 105670

Send Inquiry

*Subject:
*Purchase Time:
*Content:
*Country/Region:
*Full Name:
*Current Email:
WebSite:
*Company Name:
*Phone Number: - -
 

Auto Grade Assist

With the auto grade assist function, the operator moves the arm, the boom adjusts the bucket height automatically, tracing the target surface and minimizing digging too deep. This allows the operator to perform rough digging without worrying about the design surface, and to perform fine digging by operating the arm lever only. The working range is expanded by holding the lever to move the boom downward.

Auto Stop Control

During boom or bucket operation, the work equipment automatically stops when the bucket edge reaches the design surface, thus minimizing damage to the design surface.

Facing Angle Compass

The orientation and color of the facing angle compass’s arrow shows the operator the facing angle of the bucket edge relative to the target surface. This allows the bucket edge to be accurately positioned square with the target surface, which is useful when finishing slopes.

Komatsu intelligent Machine Control Components

Standard factory installed intelligent Machine Control system for 3D GNSS machine guidance and semi-automatic control. Sensor package includes stroke sensing hydraulic cylinders, inertial measurement units, and GNSS antennas. 

intelligent Machine Control

World’s first intelligent Machine Control excavator with semi-automatic control allows the operator to improve work efficiency as compared to conventional aftermarket machine guidance (indicate only) or manual operation. Rough digging to finish grading, intelligent Machine Control minimizes over-excavation to make every pass count. 

Minimum Distance Control

The intelligent Machine Control excavator controls the bucket by automatically selecting the point on the bucket closest to the target surface. Should the machine not be facing a sloped surface at a right angle, it will still follow the target surface and minimize digging below it.

Control Box

The monitor of the Komatsu intelligent Machine Control (control box) uses a large 12.1" (30.7 cm) touch screen for visibility and ease of use. The screen layout is customizable to display information in an easily understood fashion with a variety of views including 3D, plan, and section. 

Stroke Sensing Hydraulic Cylinder

Sensor package with stroke sensing hydraulic cylinders provides real time position, immediately displayed to the operator. This is in contrast to conventional aftermarket machine guidance (indicate only) systems with tilt sensors that require time to stabilize. 

Fuel tank 650 ltr  172 U.S. gal
Coolant 47 ltr 12.4 U.S. gal
Engine 38 ltr 10.0 U.S. gal
Final drive, each side 11 ltr 2.9 U.S. gal
Swing drive 20 ltr 5.3 U.S. gal
Hydraulic tank 248 ltr 65.5 U.S. gal
Diesel Exhaust Fluid (DEF) tank 39 ltr 10.3 U.S. gal

Steering control Two levers with pedals
Drive method Hydrostatic
Maximum drawbar pull 329 kN / 33510 kg 73,880 lb
Gradeability 35° 70%
Maximum travel speed: (Auto-Shift):
High 5.5 km/h 3.4 mph
Mid 4.2 km/h 2.6 mph
Low 3.0 km/h 1.9 mph
Service brake Hydraulic lock
Parking brake Mechanical disc brake

Model
Komatsu SAA6D125E-7*
Type
Water-cooled, 4-cycle, direct injection
Aspiration
Komatsu Variable Geometry Turbocharger with air-to-air aftercooled EGR
Number of cylinders
6
Bore 125 mm 4.92"
Stroke 150 mm 5.91"
Piston displacement 11.04 ltr 674 in³
Horsepower

SAE J1995 : Gross 270 kW 362 HP
ISO 9249/SAE J1349 : Net 268 kW 359 HP
Rated rpm
1900 rpm
Governor
All-speed control, electronic.
Fan drive method for radiator cooling
Hydraulic
*EPA Tier 4 Final emissions certified


Main pump:
Pumps for   Boom, arm, bucket, swing, and travel circuits
Type Variable displacement axial piston type
Maximum flow 780 ltr/min 206 U.S. gal/min
Hydraulic motors:
Travel 2 x axial piston motor with parking brake
Swing 1 x axial piston motor with swing holding brake
Relief valve setting:
Implement circuits 380 kgf/cm²/ 37.3 MPa 5,400 psi
Travel circuit 380 kgf/cm² / 37.3 MPa 5,400 psi
Swing circuit 285 kgf/cm²/ 27.9 MPa 4,050 psi
Pilot circuit 33 kgf/cm² / 3.2 MPa 470 psi
Hydraulic cylinders:
Number of cylinders Bore x Stroke x Rod Diameter Bore x Stroke x Rod Diameter
Boom / 2 160 mm x 1570 mm x 110 mm 6.3" x 61.8" x 4.3"
Arm / 1 185 mm x 1820 mm x 120 mm 7.3" x 71.7" x 4.7"
Bucket / 1 160 mm x 1270 mm x 110 mm 6.3" x 50" x 4.3"

Fixed Gauge  
Shoes 700 mm 28"
Operating Weight 47930 kg 105,670 lb
Ground Pressure 0.73 kg/cm² 10.38 psi
Shoes 800 mm 31.5''
Operating Weight: 48430 kg 106,770 lb
Ground Pressure 0.65 kg/cm² 9.20 psi
Shoes 900 mm 35.5"
Operating Weight: 48920 kg 107,850 lb
Ground Pressure 0.58 kg/cm² 8.32 psi

Drive method Hydrostatic motor
Swing reduction Planetary gear
Swing circle lubrication Grease-bathed
Service brake Hydraulic lock
Holding brake/Swing lock Mechanical disc brake
Swing speed 9.0 rpm
Swing torque 13414 kg•m 97,024 ft. lbs.

Center frame X-frame
Track frame Box-section
Track type
Sealed
Track adjuster Hydraulic
Number of shoes 49 each side
Number of carrier rollers 
2 each side
Number of track rollers 8 each side

Construction Machinery Online

Language Options

E-Mail: webmaster@global-ce.com TEL: 0086-10-52895329 FAX:0086-10-84673349
lmjx.net Site: International - China - U.S.A - Russia - France - Spain - Portugal - India - Germany - Saudi Arabia - Indonesia

Copyright Notice 2002-2019 global-ce.com Construction Machinery Online. All rights reserved.

Address: Room 901, Building C, Ruipu Mansion, Hongjunying South Road No.15, Chaoyang District, Beijing.100107 P.R.China