Global-CE > Haul Trucks > KOMATSUHaul Trucks > Komatsu 930E-4SE ELECTRIC TRUCKS

Komatsu 930E-4SE ELECTRIC TRUCKS

Capacity	320
Horsepower	3,500 @1900 rpm
MaxGrossVehicleWeight	1115000

Send Inquiry

*Subject:
*Purchase Time:
*Content:	Komatsu 930E-4SE ELECTRIC TRUCKS floor price
*Country/Region:
*Full Name:
*Current Email:
WebSite:
*Company Name:
*Phone Number:	- -

Feature Parameter

Body

All-welded steel flat floor body with horizontal bolsters and full canopy. Eyebrow, rear wheel rock ejectors, body up sling, and rubber mounts on frame are standard. Pivot exhaust heating optional.

Braking System

Service brakes: oil-cooled, hydraulic-actuated, multiple disc brakes at each wheel. Traction system wheel slip/slide control.

Cab

Advanced Operator Environment with integral 4-post ROPS/FOPS structure (meets J1040 Apr88), adjustable air suspension seat w/lumbar support and arm rests, passenger seat, maximum R-value insulation, tilt and telescoping steering wheel, electric windshield wipers w/washer, tinted safety glass, power windows, Komatsu Payload Weighing System, 55,000 Btu/hr heater and defroster, 21,600 Btu/hr air conditioning (HFC - 134A refrigerant).

Cooling System

L&M radiator assembly, split-flow, with deareation-type top tank measuring 3277 mm x 2164 (10'9" x 7'1").

Electrical System

4 x 8D and 2 x 30H, 220-ampere-hour batteries, bumper-mounted with disconnect switch.

Electric Drive

* Wheel motor application depends upon gross vehicle weight, haul road grade, haul road length, rolling resistance and other parameters. Komatsu and G.E. must analyze each job condition to assure proper application.

Engine

* Net flywheel power is the rated power at the engine flywheel minus the average accessory losses. Accessories include fan and charging alternator.

Power ratings above represent engine performance in accordance with SAE J1995 and J1349 conditions.

Make and model		Komatsu SSDA18V170
Fuel		Diesel
Number of cylinders		18
Operating cycle		4 cycle
Gross horsepower @ 1900 rpm	3,500 HP	2611 kW
Net flywheel power* @ 1900 rpm	3,429 HP	2558 kW
Weight (wet)	22,266 lb	10100 kg

Frame

Advanced technology, full butt-welded box sectional ladder-type frame with integral ROPS supports, integral front bumper, rear tubular cross members, steel castings at all critical stress transition zones, rugged continuous horsecollar.

Hydraulic System

Steering		Accumulator assisted with twin double acting cylinders provide constant rate steering. Secondary steering automatically supplied by accumulator.
Turning circle diameter (SAE)	97'7''	29.7 m
Reservoir	250 U.S. gal	947 L
Filtration		In-line replaceable elements
Suction		Single, full flow, 100 mesh
Hoist and steering		Dual, in-line, high pressure.
Brake component cabinet		Above deck, easily accessible with diagnostic test connections.
Hoist		Two 3-stage dual-acting outboard cylinders, internal cushion valve, over-center dampening.
Hoist times:
Power-up loaded		21 sec
Power-down		23 sec
Float-down empty		24 sec
Pumps		Two pumps, single package, end of alternator
Hoist and brake cooling		Tandem gear pump with output of 1022 lpm (270 gpm) at 1900 rpm and 17237 kPa (2,500 psi)
Steering and brake		Pressure-compensating piston pump with output of 246 lpm (65 gpm) at 1900 rpm and 18961 kPa (2,750 psi)
System relief pressures:
Hoist and brake cooling	2,500 psi	17237 kPa
Steering and brake	4,000 psi	27579 kPa
Quick disconnects standard for systems diagnostics and buddy dump.

Service Capacities

Cooling System	190 U.S. gal	719 L
Crankcase*	90 U.S. gal	341 L
Hydraulic system	350 U.S. gal	1325 L
Motor gear box (each)	25 U.S. gal	95 L
Fuel	1400 U.S. gal	5300 L
*Includes lube oil filters

Suspension

Variable rate hydro-pneumatic with integral rebound control

Tires and Rims

*Tires should meet application requirements for tkph/tmph, tread, compound, inflation pressure, ply rating or equivalent, etc.

Parameter

Floor sheet 200,000 psi / 1379 mPa tensile strength steel (two-piece)	0.63''	16 mm
Front sheet 200,000 psi / 1379 mPa tensile strength steel	0.35''	9 mm
Side sheet 200,000 psi / 1379 mPa tensile strength steel	0.31''	8 mm
Canopy sheet 100,000 psi / 690 mPa	0.19''	5 mm
Standard SAE heaped 2:1	276 yd³	211 m³
Standard Komatsu body weight	66,936 lb	30362 kg
*Komatsu must approve all bodies through a Body Application Worksheet.

Max. service apply pressure	2500 psi	17237 kPa
Total friction area per brake	15,038 in²	97025 cm²
Secondary brakes		Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
Wheel brake locks		Switch activated
Parking brakes		Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade @ maximum gross vehicle weight.
Electric dynamic retarder	Max 5400 hp 4026 kW	Continuous 3900 hp 2909 kW
Continuously rated high-density blown grids w/retard at engine idle and retard in reverse propulsion.

Alternator		24 volt, 140 amp
Lighting		24 volt
Cranking motor		two/24 volt

AC CURRENT
Alternator		GTA-39
Dual impeller in-line blower	16,000 cfm	453 m³/min
Control		AC Torque Control System
Motorized wheels*		GDY106 AC Induction Traction Motors
Ratio**		32.62:1
Speed (maximum)	40 mph	64.5 km/h

Make and model		Komatsu SSDA18V170
Fuel		Diesel
Number of cylinders		18
Operating cycle		4 cycle
Gross horsepower @ 1900 rpm	3,500 HP	2611 kW
Net flywheel power* @ 1900 rpm	3,429 HP	2558 kW
Weight (wet)	22,266 lb	10100 kg

Plate material tensile strength steel	70,000 psi	482.6 MPa
Casting material tensile strength steel	90,000 psi	620.5 MPa
Rail width	12''	305 mm
Rail depth (minimum)	34''	864 mm
Top and bottom plate thickness	1.77''	45 mm
Side plate thickness	0.98''	25 mm
Drive axle mounting		Pin and spherical bushing
Drive axle alignment		Swing link between frame and axle

Steering		Accumulator assisted with twin double acting cylinders provide constant rate steering. Secondary steering automatically supplied by accumulator.
Turning circle diameter (SAE)	97'7''	29.7 m
Reservoir	250 U.S. gal	947 L
Filtration		In-line replaceable elements
Suction		Single, full flow, 100 mesh
Hoist and steering		Dual, in-line, high pressure.
Brake component cabinet		Above deck, easily accessible with diagnostic test connections.
Hoist		Two 3-stage dual-acting outboard cylinders, internal cushion valve, over-center dampening.
Hoist times:
Power-up loaded		21 sec
Power-down		23 sec
Float-down empty		24 sec
Pumps		Two pumps, single package, end of alternator
Hoist and brake cooling		Tandem gear pump with output of 1022 lpm (270 gpm) at 1900 rpm and 17237 kPa (2,500 psi)
Steering and brake		Pressure-compensating piston pump with output of 246 lpm (65 gpm) at 1900 rpm and 18961 kPa (2,750 psi)
System relief pressures:
Hoist and brake cooling	2,500 psi	17237 kPa
Steering and brake	4,000 psi	27579 kPa
Quick disconnects standard for systems diagnostics and buddy dump.

Cooling System	190 U.S. gal	719 L
Crankcase*	90 U.S. gal	341 L
Hydraulic system	350 U.S. gal	1325 L
Motor gear box (each)	25 U.S. gal	95 L
Fuel	1400 U.S. gal	5300 L
*Includes lube oil filters

Max. front stroke	12.92''	328 mm
Max. rear stroke	9.40''	239 mm
Max. rear axle oscillation		±6.5°
*Rear suspensions are inverted.

Rock service, tubeless, radial tires
Standard tire*		53/80 R63
Taper Lock		914 mm x 1600 mm x 127 mm (36'' x 63'' x 5.0'') rim assembly Rated at 758 kPa (110 psi) cold inflation pressure for rims, 600 kPa (87 psi) for tires.

Empty Vehicle:	lb	kg
Front axle (48.5%)	230,293	104459
Rear axle (51.5%)	244,377	110847
Total (wet, 100% fuel)	474,670	215307
Loaded Vehicle at maximum GVW rating
Front axle (32.8%)	365,871	165956
Rear axle (67.2%)	748,799	339649
Total	1,115,000	505755
NOTE: GVW shall not exceed 505755 kg 1,115,000 lb including options, liners, fuel and payload, subject to application approval by Komatsu.
NOTE: Komatsu trucks comply with SAE specifications for cab noise, ROPS, steering and braking. Cover photos and illustrations may show optional equipment. Materials and specifications subject to change without notice.